flyweight
Respect the instrument and connect
Ik ben een TX816 aan het herstellen. 7 van de 8 modules komen online.
Nu is er 1 die het niet doet.
Heeft iemand hint/tips voor het troubleshooten van de TF-1 // DX7 // TX7 ?
1 module heeft 88 op het display.
Alle leds staan aan en hij reageerd niet om de push buttons.
Dit gebeurd direct by power on.
Iets later gaat wel de relais aan.
Ik heb het eeprom van een goede module omgeruild en geen verschil.
IC20 is PST518 ziet er als een soort transitor uit.
When power is ON, IC20 (PST51 generates a system reset signal.
Pin 12 (IC20) outputs a RES signal, and PIN 10 (IC20) outputs a RES signal.
The RES Signal is send to the EGS, the battery backup circuit and the output muting circuit.
Wat is EGS ?
Hoe kan ik het beste testen of de HD6303XP ok is?
Ik heb een simpele 1 kanaals scope.
Dit heb ik uit de service manual gehaald.
HD6303XP pinout beneden:
VCC = +5V
VSS = GND
Check clock with scope.
MP0 = “high”
MP1 = “low”
STBY = not used and fixed to HIGH
NMI = not used and fixed to HIGH
When power is ON, IC20 (PST51 generates a system reset signal.
Pin 12 (IC20) outputs a RES signal, and PIN 10 (IC20) outputs a RES signal.
The RES Signal is send to the EGS, the battery backup circuit and the output muting circuit.
( wat is EGS? )
HD6303XP pinout:
Nu is er 1 die het niet doet.
Heeft iemand hint/tips voor het troubleshooten van de TF-1 // DX7 // TX7 ?
1 module heeft 88 op het display.
Alle leds staan aan en hij reageerd niet om de push buttons.
Dit gebeurd direct by power on.
Iets later gaat wel de relais aan.
Ik heb het eeprom van een goede module omgeruild en geen verschil.
IC20 is PST518 ziet er als een soort transitor uit.
When power is ON, IC20 (PST51 generates a system reset signal.
Pin 12 (IC20) outputs a RES signal, and PIN 10 (IC20) outputs a RES signal.
The RES Signal is send to the EGS, the battery backup circuit and the output muting circuit.
Wat is EGS ?
Hoe kan ik het beste testen of de HD6303XP ok is?
Ik heb een simpele 1 kanaals scope.
Dit heb ik uit de service manual gehaald.
HD6303XP pinout beneden:
VCC = +5V
VSS = GND
Check clock with scope.
MP0 = “high”
MP1 = “low”
STBY = not used and fixed to HIGH
NMI = not used and fixed to HIGH
- Port 2
- -P20 (output) Midi in individual/common switch
- -p21 (output) “individual” led
- -P22 (output) “common” led
- -P23 (input) Midi message receiving led
- -P24 (output) Midi message sending led
- -P25 (output) “memory protect” Led
- -P26 (output) “Parameter change led”
- -P27 (output) “error led”
When power is ON, IC20 (PST51 generates a system reset signal.
Pin 12 (IC20) outputs a RES signal, and PIN 10 (IC20) outputs a RES signal.
The RES Signal is send to the EGS, the battery backup circuit and the output muting circuit.
( wat is EGS? )
- Port 5
- -P50 (input) battery voltage detection.
- -P51 (input) midi out slot switching
- -P52 (input) This is a memory ready terminal to leghten the E (enable) clock “high” period.
this terminal is fixed to high logic level. So the E clock is a normal continuous clock. - -P53 (input) HALT terminal – fixed to high – not used
- -P54 (input) fixed to high – not used
- -P55 (input) “individual/common” switch detection
- -P56 (input) “memory protect” switch detection
- -P57 (input) “select” switch detection
- Port 6
-P60 – P67 are connected to the HA17408 DAC IC10 which outputs the data for the level attendator and battery voltage comparator
- Bus Port60 - P67 represent the address bus, and D0 throught D7 represents the data bus.
- BA HALT terminal, fixed to high
- LIR not used
- R/W This outputs a “high” logic level when the MPU is in the read mode, and a “low” logic level the MPU is in the write mode.
- WR outputs a “low” when MPU in write mode
- RD outputs a “low” when MPU in read mode
- E this is an enable terminal that outputs the systemclock
HD6303XP pinout: