klinkske
zoekt een GAS masker.
Je kan er ook 1 met midi bij turnlab kopen voor 1100 euro méér 
Mijn polysix gaat in de verkoop, is netjes, heeft kenton midi, nooit een batterij lek gehad en recent nog nagekeken door een man met ervaring.
prijs is 1800 euro vast.
Waarom 1800? Kenton midi niet onderschatten zei mijn tech.
Ik gebruik m niet, staat daarom te wachten op een beziger baasje.
Ophalen graag, Ik kan m eventueel leveren na voorschot te hebben gekregen.
De foto met witte sticker boven de midi is ter info (zodat je weet wat in out is) want die sticker is verwijderd.
Geen interesse in moderne ruil.
Info over de midi kit:
kentonuk.com
deze kit kost 504 pond excl verzend en import. Ja dat lees je goed.
For incoming MIDI:
Any MIDI channel can be selected
Notes (MIDI note numbers 36 – 96) – transpose possible
Program change (numbers 1 – 40)
Pitchbend – (bends up and down a fifth)
Mod Wheel
Filter cutoff frequency (of low pass filter)
Volume
Sysex dump & load for programs
By default:
pitchbend is controlled by pitchbend messages
mod wheel is controlled by Mod Wheel (CC#1) and also by Aftertouch messages
filter cutoff is controlled by CC#16
Volume is controlled by MIDI volume (CC#7)
however, any controller or aftertouch or velocity can be mapped to control other things so for example velocity could be mapped to control volume.
For outgoing MIDI:
Any MIDI channel can be selected
Notes (MIDI note numbers 36 – 96) – transpose possible
Program changes 1 to 61 can be sent using a button press followed by a key press
No other MIDI can be sent – the retrofit is primarily intended to allow the synth to be played from a MIDI master keyboard or sequencer.
Hardware:
MIDI In, Out & Thru sockets
Push button (for programming the MIDI setup)
Setups are stored in non-volatile memory (Eeprom)
Mijn polysix gaat in de verkoop, is netjes, heeft kenton midi, nooit een batterij lek gehad en recent nog nagekeken door een man met ervaring.
prijs is 1800 euro vast.
Waarom 1800? Kenton midi niet onderschatten zei mijn tech.
Ik gebruik m niet, staat daarom te wachten op een beziger baasje.
Ophalen graag, Ik kan m eventueel leveren na voorschot te hebben gekregen.
De foto met witte sticker boven de midi is ter info (zodat je weet wat in out is) want die sticker is verwijderd.
Geen interesse in moderne ruil.
Info over de midi kit:
PolySix - Kenton Electronics
PLEASE NOTE: Installing a retrofit kit is a skilled job which should be undertaken only by a competent synth service engineer or installed by us at our premises in Tadworth, just outside London. Note also that retrofit kits are always built to order after your payment has been processed. It then...
kentonuk.com
deze kit kost 504 pond excl verzend en import. Ja dat lees je goed.
Retrofit Kit
This retrofit kit for the Korg Polysix adds the following MIDI control:For incoming MIDI:
Any MIDI channel can be selected
Notes (MIDI note numbers 36 – 96) – transpose possible
Program change (numbers 1 – 40)
Pitchbend – (bends up and down a fifth)
Mod Wheel
Filter cutoff frequency (of low pass filter)
Volume
Sysex dump & load for programs
By default:
pitchbend is controlled by pitchbend messages
mod wheel is controlled by Mod Wheel (CC#1) and also by Aftertouch messages
filter cutoff is controlled by CC#16
Volume is controlled by MIDI volume (CC#7)
however, any controller or aftertouch or velocity can be mapped to control other things so for example velocity could be mapped to control volume.
For outgoing MIDI:
Any MIDI channel can be selected
Notes (MIDI note numbers 36 – 96) – transpose possible
Program changes 1 to 61 can be sent using a button press followed by a key press
No other MIDI can be sent – the retrofit is primarily intended to allow the synth to be played from a MIDI master keyboard or sequencer.
Hardware:
MIDI In, Out & Thru sockets
Push button (for programming the MIDI setup)
Setups are stored in non-volatile memory (Eeprom)
