Er komt binnenkort een nieuwe versie van de Kiwi mod uit voor de JX3P
The JX-3P Matrix Upgrade features:
-•1024 Tones & 8 Sequences can be stored and edited, Sequences can be optionally linked to tones. It is also possible to edit any Tone or Seq.
•A Pulse Width Module is included with the Kiwi3P Matrix. This allows Pulse Width control and waveform mixing.
•After tuning during the Kiwi-3P Matrix upgrade install a Saw wave tuning offset keeps the wave shape correct for all voices across the full range. Due to component tolerances this is not possible on the original JX-3P hardware.
•A Chorus Control board is included with the Kiwi3P Matrix. This allows variable Chorus Rate and manual control.
•Saw, Pulse Width & Square Waveforms can be solo or mixed in any combination.
•Sysex support for all and MidiCC for most parameters, Midi Sysex support for Tone Dump & Load
•Patch Editor Control of Parameters (requires PE v 8.3 or later)
•MidiQuest 12 includes editors for all the Kiwi range and it will work with any midi editor. The manual has full midi details.
•Full Matrix system with 29 Source and 40 Destination types.
•Key Assign Modes are Poly Single, Poly Dual, Poly Triple, Unison & Solo
•Each Key Assign mode can have Rotate/Reassign, Staccato/Legato, Steal/No Steal with five steal modes (Highest, Lowest, Oldest, Newest, Quietest)
•Portamento in all key modes
•Note Detune available in all key modes, DCO 1 & 2 have separate Tune controls (±12 semitones) and DCO2 has a Fine Tune (±50 cents). There is also an Analogue Feel parameter that adds a small random detune to notes.
•Master Synth Fine Tune adjust in both hardware and software.
•Three independent envelope generators. These are traditional ADSR type and are modeled on the Original JX-3P. Each ENV Mod can select from ENV 1 - 3 and has an Inverted or Normal modes. These are faster than the traditional JX-3P envelopes and are matrix sources.
•Three independent Low Frequency Oscillators with 6 waveforms each. Each LFO Mod can select from LFO 1-3 and they are a matrix source. LFOs can be plus and minus base note or plus base note only.
•Midi Note Aftertouch (Channel & Note), Midi and Internal Modulation Level and Midi Note Dynamics are all Matrix sources and can be sent any Matrix Destination.
•LFO Button is a Matrix Source and can inject mod control to any matrix destination.
•Bend Lever is coded to DCO Frequency for Bend but is also a Matrix Source which can be sent to any Destination
•Front panel editing is available for all parameters. These can be edited via midi or the PG-200.
•Master, Sequencer and Arpeggiator clocks can optionally display on the front panel
•Key transpose allows transposition to any key. The range for this is -1 Octave to +2 Octaves
•CHORD MODE
•Any chord with up to 6 notes can be set and played from any key
•ARPEGGIATOR
•The Arpeggiator is clocked from the Master Clock and can be independently divided to Half Note, Quarter Note, 1/8 Note, 1/8 Note Half Swing, 1/8 Note Full Swing, 1/8 Note Triplets, 1/16 Note, 1/16 Note Half Swing, 1/16 Note Full Swing, 1/16 Note Triplets, 1/32 Note, 1/32 Note Triplets, 1/64 Note.
•Arp modes are Up, Down, Up and Down, Random, As Played, 1, 2, 3 or 4 octaves
•Arp can be Started, Stopped & Continued using Midi Commands
•Appeggiator will Output Midi Data
•SEQUENCER
•8 separate 124 Max step Polyphonic sequences can be created and stored
•Sequences can be edited
•The Sequencer is clocked from the Master Clock and can be independently divided to Half Note, Quarter Note, 1/8 Note, 1/8 Note Half Swing, 1/8 Note Full Swing, 1/8 Note Triplets, 1/16 Note, 1/16 Note Half Swing, 1/16 Note Full Swing, 1/16 Note Triplets, 1/32 Note, 1/32 Note Triplets, 1/64 Note.
•Sequencer can be Started, Stopped & Continued using Midi Commands
•Sequencer will Output Midi Data
•PG-200
•Full PG-200 support
•PG-200 will output midi data
The
The JX-3P Matrix Upgrade features:
-•1024 Tones & 8 Sequences can be stored and edited, Sequences can be optionally linked to tones. It is also possible to edit any Tone or Seq.
•A Pulse Width Module is included with the Kiwi3P Matrix. This allows Pulse Width control and waveform mixing.
•After tuning during the Kiwi-3P Matrix upgrade install a Saw wave tuning offset keeps the wave shape correct for all voices across the full range. Due to component tolerances this is not possible on the original JX-3P hardware.
•A Chorus Control board is included with the Kiwi3P Matrix. This allows variable Chorus Rate and manual control.
•Saw, Pulse Width & Square Waveforms can be solo or mixed in any combination.
•Sysex support for all and MidiCC for most parameters, Midi Sysex support for Tone Dump & Load
•Patch Editor Control of Parameters (requires PE v 8.3 or later)
•MidiQuest 12 includes editors for all the Kiwi range and it will work with any midi editor. The manual has full midi details.
•Full Matrix system with 29 Source and 40 Destination types.
•Key Assign Modes are Poly Single, Poly Dual, Poly Triple, Unison & Solo
•Each Key Assign mode can have Rotate/Reassign, Staccato/Legato, Steal/No Steal with five steal modes (Highest, Lowest, Oldest, Newest, Quietest)
•Portamento in all key modes
•Note Detune available in all key modes, DCO 1 & 2 have separate Tune controls (±12 semitones) and DCO2 has a Fine Tune (±50 cents). There is also an Analogue Feel parameter that adds a small random detune to notes.
•Master Synth Fine Tune adjust in both hardware and software.
•Three independent envelope generators. These are traditional ADSR type and are modeled on the Original JX-3P. Each ENV Mod can select from ENV 1 - 3 and has an Inverted or Normal modes. These are faster than the traditional JX-3P envelopes and are matrix sources.
•Three independent Low Frequency Oscillators with 6 waveforms each. Each LFO Mod can select from LFO 1-3 and they are a matrix source. LFOs can be plus and minus base note or plus base note only.
•Midi Note Aftertouch (Channel & Note), Midi and Internal Modulation Level and Midi Note Dynamics are all Matrix sources and can be sent any Matrix Destination.
•LFO Button is a Matrix Source and can inject mod control to any matrix destination.
•Bend Lever is coded to DCO Frequency for Bend but is also a Matrix Source which can be sent to any Destination
•Front panel editing is available for all parameters. These can be edited via midi or the PG-200.
•Master, Sequencer and Arpeggiator clocks can optionally display on the front panel
•Key transpose allows transposition to any key. The range for this is -1 Octave to +2 Octaves
•CHORD MODE
•Any chord with up to 6 notes can be set and played from any key
•ARPEGGIATOR
•The Arpeggiator is clocked from the Master Clock and can be independently divided to Half Note, Quarter Note, 1/8 Note, 1/8 Note Half Swing, 1/8 Note Full Swing, 1/8 Note Triplets, 1/16 Note, 1/16 Note Half Swing, 1/16 Note Full Swing, 1/16 Note Triplets, 1/32 Note, 1/32 Note Triplets, 1/64 Note.
•Arp modes are Up, Down, Up and Down, Random, As Played, 1, 2, 3 or 4 octaves
•Arp can be Started, Stopped & Continued using Midi Commands
•Appeggiator will Output Midi Data
•SEQUENCER
•8 separate 124 Max step Polyphonic sequences can be created and stored
•Sequences can be edited
•The Sequencer is clocked from the Master Clock and can be independently divided to Half Note, Quarter Note, 1/8 Note, 1/8 Note Half Swing, 1/8 Note Full Swing, 1/8 Note Triplets, 1/16 Note, 1/16 Note Half Swing, 1/16 Note Full Swing, 1/16 Note Triplets, 1/32 Note, 1/32 Note Triplets, 1/64 Note.
•Sequencer can be Started, Stopped & Continued using Midi Commands
•Sequencer will Output Midi Data
•PG-200
•Full PG-200 support
•PG-200 will output midi data
The
